Already a subscriber?
MADCAD.com Free Trial
Sign up for a 3 day free trial to explore the MADCAD.com interface, PLUS access the
2009 International Building Code to see how it all works.
If you like to setup a quick demo, let us know at support@madcad.com
or +1 800.798.9296 and we will be happy to schedule a webinar for you.
Security check
Please login to your personal account to use this feature.
Please login to your authorized staff account to use this feature.
Are you sure you want to empty the cart?
Significant Changes to the IPC, IMC, and IFGC, 2012 Edition, 2012
- Cover
- Contents
- PART 1 International Plumbing Code (Chapters 1 through 14) [Go to Page]
- 202 Plumbing Fixture Definition
- 202 Plumbing Appliance Definition
- 202 Grease Interceptor Definition
- 303.1, 303.4 Material Identification and Third-Party Certification
- 308.9 Parallel Water Distribution Systems
- 315.1 Sealing of Annular Spaces at Penetrations
- Table 403.1 Minimum Number of Required Plumbing Fixtures
- 403.2 Separate Toilet Facilities in Group M Occupancies
- 403.2.1 Family or Assisted-Use Toilet Facilities Serving as Separate Facilities
- 403.3.2 Relationship of Toilet Rooms and Food Preparation Areas
- 403.3.6 Locking of Toilet Room Doors
- 403.5 Drinking Fountain Locations
- 405.3.1 Minimum Water Closet Compartment Size
- 405.4 Floor and Wall Drainage Connections
- 407.2 Bathtub Waste Outlets and Overflows
- 410 Minimum Required Number of Drinking Fountains
- 417.5.2.6 Shower Pan Liner Materials
- 424.9 Water Closet Personal Hygiene Devices
- 504.4.1 Water Heater Storage Tank Relief Valves
- 504.7 Water Heater Pans
- 605 Polyethylene of Raised-Temperature (PE-RT) Plastic Tubing
- Table 605.3 Polyethylene (PE) Water Service Pipe
- Table 605.3 PEX Water Service Pipe
- 606.7 Labeling of Water Distribution Pipes in Bundles
- 607.1.1 Water-Temperature-Limiting Means
- 607.2 Hot or Tempered Water Supply to Fixtures
- 607.5 Hot Water Piping Insulation
- 608.8 Identification of Nonpotable Water
- 704.3, 711.2.1 Horizontal Branch Connections
- Table 709.1 Drainage Fixture Units for Bathroom Groups
- 712.3.3 Sump Pump and Ejector Discharge Pipe and Fittings
- 712.3.5 Sump Pump Connection to the Drainage System
- 715.1 Fixture Protection from Sewage Backflow
- 802.1.8 Indirect Discharge of Food Preparation Sinks
- 802.2 Installation of Indirect Waste Piping
- 802.3 Prohibited Locations for Waste Receptors
- 901.3, 918.8 Air Admittance Valves for Chemical Waste Vent Systems
- 903.5 Location of Vent Terminals
- 915.2 Combination Waste and Vent System Sizing
- 917 Single-Stack Vent Systems
- 1002.1 Floor Drains in Multi-Level Parking Structures
- 1003.1 Interceptors and Separators
- 1003.3.1 Alternate Grease Interceptor Locations
- 1003.3.4 Hydromechanical Grease Interceptors
- 1105 Roof Drain Strainers
- 1107 Siphonic Roof Drainage Systems
- Chapter 13 Gray-Water Recycling Systems
- PART 2 International Mechanical Code (Chapters 1 through 15) [Go to Page]
- 102.3 Maintenance
- 202 Environmental Air
- 306.5 Equipment and Appliances on Roofs or Elevated Structures
- 308.5 Labeled Assemblies
- 401.4 Intake Opening Location
- Table 403.3 Minimum Ventilation Rates for Nail Salons
- 404.1 Enclosed Parking Garages
- 501.2, 506.4 Independent Exhaust Systems Required
- 505.1 Domestic Kitchen Exhaust Systems
- 506.3.7.1 Grease Reservoirs
- 506.3.8 Grease Duct Cleanouts and Other Openings
- 506.3.9 Grease Duct Horizontal Cleanouts
- 506.3.10 Underground Grease Duct Installations
- 506.3.11.2 Field-Applied Grease Duct Enclosures
- 507.2 Type I or Type II Hood Required
- 507.2.1 Type I Hoods
- 507.2.1.1 Operation of Type I Hoods
- 507.2.1.2 Exhaust Flow Rate Label of Type I Hoods
- 507.2.2 Type II Hoods
- 507.10 Hoods Penetrating a Ceiling
- 510.7 Fire Suppression Required for Hazardous Exhaust Ducts
- 601.4 Contamination Prevention in Plenums
- 602.2.1 Materials within Plenums
- 603.7 Rigid Duct Penetrations
- 603.9 Duct Joints, Seams, and Connections
- 603.17, 202 Air Dispersion Systems
- 805.3 Factory-Built Chimney Offsets
- 901.4 Fireplace Accessories
- 928 Evaporative Cooling Equipment
- 1101.10 Locking Access Port Caps
- 1105.6, 1105.6.3 Machinery Room Ventilation
- 1106.4 Flammable Refrigerants
- PART 3 International Fuel Gas Code (Chapters 1 through 8) [Go to Page]
- 202, 401.9, 401.10, 404.1 Identification, Testing and Certification
- 308.1 Clearance to Combustible materials
- 404.2 CSST piping systems
- 404.18 Prohibited Devices
- 408.4 Sediment Traps
- 410.4 Excess Flow Valves
- 202, 410.5 Flashback Arrestor Check Valve
- 618.4 Prohibited Sources
- Index [Go to Page]
- A
- B
- C
- D
- E
- F
- G
- H
- I
- L
- M
- N
- O
- P
- R
- S
- T
- U
- V
- W [Go to Page]