Abstract
This standard specification establishes the requirements for seamless copper tube coils, suitable for use in refrigeration and air conditioning or other uses, such as oil lines and gasoline
lines. The material of manufacture shall be cast billet, bar, tube and so forth of Copper Alloys No. C10200, C10300, C10800, C12000, or C12200. The tube shall be manufactured by such hot and
cold working processes needed to produce a homogeneous, uniform wrought structure. The tube shall be cold drawn to the prescribed finish size and wall thickness. When the cold-drawn temper is
required, the final drawing operation shall conform to the specified temper properties. When the annealed temper is required, the tube shall be annealed after the final cold draw to the
specified temper properties. The product shall conform to the prescribed electrical mass resistivity, tensile strength, yield strength, Rockwell hardness, and expansion. Each tube shall be
subjected to an eddy-current test. Particular coppers shall be tested to meet the cuprous oxide, embrittlement, and cleanness requirements.
This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for
its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
1. Scope
1.1 This specification establishes the requirements for seamless copper tube in coils, suitable for use in refrigeration and air conditioning or other uses, such as oil lines and gasoline
lines.
1.2 Units The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.3 The tube shall be produced of the following coppers. Unless otherwise specified, tubes made from any one of these coppers may be supplied:
Copper Alloy
UNS No.
|
Previously Used
Designation
|
Type of Copper
|
|
|
|
|
C10200
|
OF
|
Oxygen-free without residual deoxidants A
|
|
C10300
|
...
|
Oxygen-free, extra low phosphorus A
|
|
C10800
|
...
|
Oxygen-free, low phosphorus A
|
|
C12000
|
DLP
|
Phosphorized, low residual phosphorus
|
|
C12200
|
DHP
|
Phosphorized, high residual phosphorus
|
A See Classification B224 .
1.4 The following safety hazards caveat pertains to the test method portion, Section 17, of this specification. This
standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and
health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
ASTM Standards
B153 Test Method for Expansion (Pin Test) of Copper and Copper-Alloy Pipe and Tubing
B170 Specification for Oxygen-Free Electrolytic Copper--Refinery Shapes
B193 Test Method for Resistivity of Electrical Conductor Materials
B224 Classification of Coppers
B251 Specification for General Requirements for Wrought Seamless Copper and Copper-Alloy Tube
B577 Test Methods for Detection of Cuprous Oxide (Hydrogen Embrittlement Susceptibility) in Copper
B601 Classification for Temper Designations for Copper and Copper Alloys--Wrought and Cast
B846 Terminology for Copper and Copper Alloys
E2 Methods of Preparation of Micrographs of Metals and Alloys (Including Recommended Practice for Photography As Applied to Metallography); Replaced by E 883
E3 Guide for Preparation of Metallographic Specimens
E8/E8M Test Methods for Tension Testing of Metallic Materials
E18 Test Methods for Rockwell Hardness of Metallic Materials
E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E53 Test Method for Determination of Copper in Unalloyed Copper by Gravimetry
E62 Test Methods for Chemical Analysis of Copper and Copper Alloys (Photometric Methods)
E112 Test Methods for Determining Average Grain Size
E243 Practice for Electromagnetic (Eddy-Current) Examination of Copper and Copper-Alloy Tubes
E255 Practice for Sampling Copper and Copper Alloys for the Determination of Chemical Composition
E2575 Test Method for Determination of Oxygen in Copper and Copper Alloys
Keywords
coils; copper tubes; seamless; UNS No. C10200; UNS No. C10300; UNS No. C10800; UNS No. C12000; UNS No. C12200; Coiled copper tube; Seamless Cu/Cu alloy tube--specifications; UNS
C10200--pipe/tube (seamless/welded); UNS C10300 (oxygen-free extra low phosphorus copper (OFXLP)); UNS C10300--pipe/tube (seamless/welded); UNS C10800--pipe/tube (seamless/welded); UNS
C12000--pipe/tube (seamless/welded); UNS C12200--pipe/tube (seamless/welded) ICS Number Code 2200; 77.150.30 (Copper products)
DOI: 10.1520/B0743-12
ASTM International is a member of CrossRef.
ASTM B743
