FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-D6611 2007ASTM D6611 - 00(2007)Standard Test Method for Wet and Dry Yarn-on-Yarn Abrasion ResistanceActive Standard ASTM D6611 | Developed by Subcommittee: D13.19 Book of Standards Volume: 07.02 ASTM D6611Significance and Use This test method is intended for testing dry and wet abrasion resistance of manufactured fiber yarns. This test method is especially useful for ropes intended for use in the marine environment. The test method has been used with yarns having linear densities ranging from 70 to 300 tex, but may be used with yarns outside these ranges. Limited interlaboratory correlation testing has been conducted to date. Single-laboratory testing, in accordance with ASTM practices, has now been conducted. Additional interlaboratory testing, in accordance with ASTM practices, will be conducted after approval of a definitive test method. Test results should be used with caution pending completion of interlaboratory testing. This test method is not recommended for acceptance testing of commercial shipments in the absence of reliable information on between-laboratory precision. If there are differences of practical significance between reported test results for two or more laboratories, comparative tests should be performed to determine if there is a statistical bias between them, using competent statistical assistance. As a minimum the test samples used should be as homogeneous as possible, be drawn from the material from which the disparate test results were obtained, and be randomly assigned in equal numbers to each laboratory for testing. Other materials with established test values may be used for this purpose. The test results from the two or more laboratories should be compared using a statistical test for unpaired data, at a probability level chosen prior to testing. If a bias is found, either its cause must be found and corrected, or future test results must be adjusted in consideration of the known bias. This test method is conducted at one or several applied tensions that may depend upon the yarn material and size. The number and magnitudes of applied tensions and the number of eight specimen sets generally are agreed upon in a material specification or contract order. Guidance on determining the appropriate number and magnitudes of applied tensions is given in Annex A2. 1. Scope 1.1 This test method describes the measurement of abrasion resistance properties for manufactured fiber yarns in dry and wet conditions. 1.2 This test method applies to manufactured yarns used in rope making. 1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses are provided for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM Standards D123 Terminology Relating to Textiles D1776 Practice for Conditioning and Testing Textiles D2904 Practice for Interlaboratory Testing of a Textile Test Method that Produces Normally Distributed Data Keywords abrasion; rope; yarn; Abrasion resistance--textile fabrics/fibers; Dry abrasion resistance; Wet abrasion resistance; Yarn properties; ICS Code ICS Number Code 59.080.20 (Yarns) DOI: 10.1520/D6611-00R07 ASTM International is a member of CrossRef. ASTM D6611This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|