ASTM E310-99(2004)e1
Historical Standard: ASTM E310-99(2004)e1 Standard Reference Radiographs for Tin Bronze Castings
SUPERSEDED (see Active link, below)
ASTM E310
1. Scope
1.1 These reference radiographs are reproductions of original radiographs and illustrate various types and degrees of discontinuities occurring in tin bronze and related types of alloys. The reference radiograph films are an adjunct to this document and must be purchased separately from ASTM International if needed. They are intended to provide the following:
1.1.1 A guide to the recognition of common discontinuities and their differentiation both as to type and severity level.
1.1.2 A standard nomenclature for reference in acceptance standards, specifications and drawings.
1.1.3 A source of reference radiographs from which manufacturers and purchasers may, by mutual agreement, select particular radiographs to serve as standards representing minimum acceptability. The standards so established are identified by an alphabetic defect type and severity level (or class) designation.
1.2 The original radiographs are of discontinuities in sand cast 88:8:4 Cu-Sn-Zn, 'G' type, bronze alloy plates. These discontinuities are representative of those found in wide solidification range copper-tin base alloys. The following ASTM specifications illustrate alloys covered by these standards; however, it is intended that these reference radiographs also apply to related Government and commercial material specifications:
Similar to MIL-B-16541.Similar to MIL-B-16444.
| Valve bronze castings | B 61 |
| Composition bronze or ounce metal castings | B 62 |
| Tin bronze sand castings | B 584 |
| Leaded red brass sand castings | B 584 |
| Copper-base alloy centrifugal castings (as applicable) | B 271 |
1.3 The discontinuity types and severity levels represented by the reference radiographs are shown in , which also indicates the code designation for each discontinuity type.
1.4 The use of this document is not intended to be restricted to the specific energy level or to the absolute thickness limits that are contained in the document title. The title is intended to be descriptive and not restrictive. The document may be used, where there is no other applicable document, for other energy levels or thicknesses, or both, for which it is found to be applicable and for which agreement has been reached between purchaser and manufacturer.Note 1The reference radiographs consist of twenty-two 21/2 by 51/2-in. [63.5 by 139.7-mm] radiograph reproductions of low voltage X rays. Fifteen of these were made with newly developed 1-in. [25.4 mm] plate castings and seven were made with 3/4-in. plate castings used originally for documents NAVSHIPS 250-537-1 and -2. The new plate castings cover Gas Porosity, Linear Shrinkage, and Feathery Shrinkage discontinuity types.
1.5 The values stated in inch-pound units are to be regarded as the standard.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
ASTM Standards
B61 Specification for Steam or Valve Bronze Castings
B62 Specification for Composition Bronze or Ounce Metal Castings
B271 Specification for Copper-Base Alloy Centrifugal Castings
B584 Specification for Copper Alloy Sand Castings for General Applications
E94 Guide for Radiographic Examination
E242 Reference Radiographs for Appearances of Radiographic Images as Certain Parameters are Changed
E1316 Terminology for Nondestructive Examinations
Keywords
brass; casting discontinuities; copper; gamma ray; reference radiographs; tin bronze; valve bronze; X-ray; Bronze castings--specifications; Castings; Copper alloy castings; Diffraction mottling; Reference radiographs; Tin metals/alloys;
ICS Code
ICS Number Code 77.040.20 (Non-destructive testing of metals); 77.150.60 (Lead, zinc and tin products)
DOI: 10.1520/E0310-99R04E01
ASTM International is a member of CrossRef.
